Hot Water Heater Not Working | Repair And Replace Heater Working

Both gassed water heaters and electric water heaters may look alike at a glance. And both types of water heaters do have steel insulated tank jackets for the purpose of maintaining adequate heat in them. But they are quite different in their own ways.

Because of this reason, we need to know how to troubleshoot when your electric hot water heater isn’t working. So, it’s important to look at some of the differences of them first, when comparing the electric water heater and gas water heater.

The electric water heater’s temperature is generated by two elements. The two heating elements comprise of the upper element as well as the lower element that’s connected into the water tank. The other type of water heaters uses a gas burner which operates as a water heating mechanism, at the bottom of the tank.

You May Like: Water Line Pressure Relief Valve Leaking | Leaking Pressure Relief Valve

[wp_ad_camp_1]

Problems with your electric hot water heater

If your hot water heater not working electric model, then the problem is with your heating element. You don’t even need to bother yourself on repairing it since you can replace it easily.
Issues with your electric hot water heater could affect you in two ways. Either you are getting less hot water or no hot water at all.

Electric water heaters Are high geared and high-powered pieces of equipment. Make sure you turn it off prior to checking any component of your water heater.

That 240-volt Must be handled carefully at all times, so it’s a good idea to turn the circuit breaker off too if you want to be a hundred percent sure. Although this is an additional precaution, you can test the wires with a tester in order to make sure that the power is completely off before meddling with the wires.

No Hot Water because your hot water heater not working electrically

No hot water means no electricity in a nutshell. Once elaborated, it’s a switch that’s getting tripped regularly or it could be the consequence of failing elements.

If that’s the case, you may have to evaluate this water heater’s tripping issue first. To confirm that, you will have to check the circuit breaker first. The solution is simple. Locate it first, and if it’s turned off automatically, switch it on again.

But if the issue isn’t with the circuit breaker, then you will have to pull out the access panel’s element that’s right at the top of your heater. Take the insulation out of the plastic guard carefully. Try to keep away from the electric wires.

Push the reddish knob and shut off the reset button. Now you can wrap it with insulation and turn the heater’s circuit breaker back on. That should get your hot water heater back on track. If it doesn’t, then check both of the heating elements and go for a Substitution if required.

Can’t get enough of hot water, but there’s just not enough hot water

This is very common. It’s not that you don’t have hot water, but what you get isn’t adequate. A reason for this could be that your appliance does not have the capacity to meet your requirement. Just think about it for a moment before thinking of replacing it first. Is our daily demand for hot water greater than the ability of the hot water heaters supplying capacity?

The reason for this may be the number of family members who were present when you purchased your hot water heater. But with time family members kept on adding so is the need for hot water. And unfortunately, your hot water heater only produces the same amount of hot water regardless of your daily requirement.

Most water heaters have the ability to produce 70 to 80% of hot water. So, if you think that your requirement exceeds this, you can always think of reducing the usage by doing washing during a particular time frame.

For example, you can think of doing dishwashing all at once in order to minimize the hot water usage. This method will also reduce wastage and promote efficiency.

How to test your water heater’s defect while having fun under the shower

Using your heater within a limited time frame will definitely work if your hot water heater not working electrically, mainly if it has a capacity problem. But what if it does not, and it seems to produce a much lesser quantity than it used to, all of a sudden?

Then there’s a good chance that both the upper element and the lower element have failed in this situation. This will result in you experiencing cold water showers on and off. With that being said, what if there’s a better way in finding where the defect is?

The simplest way of putting it is, if the heat is really inadequate, then the defect is in the upper element. But if you feel that the hot water is turned into cold water in a very short period of time, then that is an indication of a malfunction in the lower heating element. The easiest way of determining this is when you are under the shower.

What do you do when it gets just too hot in there?

The most common problem we have in our homes is that the hot water heater not working electric device, due to the lack of heat that’s being generated. But there can be situations where the temperature of the water is much more than you can bear up.

Getting overheated water from your hot water heater could be a result of a thermostat that’s set at a level that’s over and above. Before we do anything else it’s important to check our thermostat first. Just like what we did with the access panel earlier, take the plastic guard out of the heating element.

But make sure not to touch the electric wires directly when doing it. Also, you can do some wire testing with the tester as an additional safety measure.

Once everything is clear, both of the thermostats must be checked individually. The only thing is that, you’ll need to make sure that both of those are set at an equal temperature.

You May Like: Water Heater Pressure Relief Valve Leaking | How to Fix Leakage 2021